Thursday, September 26, 2019

Quilt Ladder Tutorial

I have a special guest blogger for you today! Recently my awesome hubby, Rick, build me some quilt racks for our home. They are simple to make and so sturdy. He has created this tutorial and given me permission to share it with you. Enjoy!


Material List
1) 3 - 2"x4"x8'      Select best looking, straightest pieces with the fewest knots and least warp
2) 12 - #2 Phillips 10 x 2 1/2" Wood Screws
3) 1 Quart paint color of choice or stain of choice
4) 1 Bristle brush or 1 pack of 1 1/2" sponge brushes
5) Adhesive Chair Leg Pads (Cut to size or use push pin types)

Tools
1) Saw (Power Miter Saw or Circular Saw preferred)
2) Power Drill (Use 1/8" bit for pilot holes and use Phillip head bit for wood screws)
3) Sand Paper to prepare surfaces for finish
          Sand by hand or with Power Sander (Palm Sander)
          Grit Numbers from 100 - 180 perform well with both hand sanding and power sanding
4) Small Level
5) T-Square for drawing straight, level lines

Prepare the Pieces
Cut 1' off each of the 3 - 2"x4"x8' pieces using the saw
      This is a total of 3 cuts, 1 for each board
      Remove / cut off the least attractive ends that have the most flaws
Select the best looking (with the least flaws) 2 - 7' long pieces to be used as the sides, considering which should be top end, front facing and side facing
      These will now be known as the "side rails"
      Use a pencil to note Top, Front
At the bottom of each side rail (2), make an angled cut so when the finished rack leans against a wall, the bottom of the side rails will be flat against the floor
      Lean each side rail against a wall at the desired "lean" angle
      Set the level flat on the floor against the rail
      Using a pencil make a line on the side of the rails using the top of the level as a guide
          This will give you the necessary angle to cut
Using the saw, cut along the "angled" mark at the bottom of the 2 side rails
Set aside the side rails

Cut the 1 remaining 7' long piece in to equal lengths of 14"
      Resulting 6 pieces will be the "cross bars"
      Measure 14" from one end and mark a line using the T-Square
          Continue measuring every 14"
          Should have a total of 5 lines
          Make 5 cuts, one cut on each of the 5 lines drawn

Sand all pieces (side rails and cross bars) as smooth as desired

When satisfied with sanding, paint or stain all pieces
      Apply as many coats as desired


Assemble
Take one side rail...
Starting at the top of the selected side rail, on the wider (2 1/2") side that will be on the inside of the finished rack, measure down from the top of the side rail 6" and mark a line across using the T-Square
Then measure down 1 1/2" from the first line and mark a line across
      A cross bar will fit between the two lines just marked
Then measure 12" down from the second line and mark a line across
Then measure 1 1/2" down and mark a line across
Repeat marking the side rail for a total of 6 cross bars
Repeat all steps on the second side rail

Take one side rail...
On the outside of the selected side rail, drill pilot holes through the side raid in the middle of the lines denoting where the cross bars go
      You will have to approximate (eye-ball) where to drill
      One hole for each cross bar
Repeat on second side rail

Final Assembly
Attach cross bars to the side rails using the pre-drawn lines as guides (cross bars should be set inside each set of drawn lines
      Screw (using the drill) in to place using the pre-drilled pilot holes and wood screws
      Fasten (screw) cross bards to one side rail at a time
If desired, attach Chair Leg pads to the bottom of each side rail (on angled cut) to prevent scratching of the floor and sliding





6 comments:

Maria said...

Perfect ladder for displaying your quilts Ellyn.
Thanks Rick for the tutorial.

Jayne said...

That's awesome Ellyn! Husbands with carpentry skills for us quilters is a must!

mari hafenstein said...

been wanting a couple of these for years. I have a great woodworker hubby but he is limited on time. Thx Rick for spelling it out. We have an anniversary coming up...guess what I am asking for?!

Debbie said...

This is great! And how nice Rick was willing to build for you again - AND share with us. Thank him!

Patricia said...

Thank you, my husband can do that !

GrandmaCindy said...

I think he could sell them. Nrsi2000@aol.com